Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Georgetown?
Gate repair in Georgetown typically costs $185 to $650 for a manual gate and $280 to $1,100 for an electric gate, depending on the operator, the part that failed, and whether the gate needs a site visit before we can quote exact work. Most common electric gate failures, including a dead operator, a misaligned photo eye, or a slipping chain, land in the $280 to $520 range. Larger jobs, such as a bent slide track or a commercial operator rebuild, run higher. The written estimate you get after we look at the gate sets the final price, and the estimate itself is free.
Georgetown’s gate stock skews residential. The older neighborhoods off the courthouse square and the newer subdivisions off Williams Drive and Ronald Reagan Boulevard both favor automatic swing gates on driveways and automatic slide gates on side entries. Limestone ground across much of the city makes digging post footings slow work, and that labor turns up in the price of any job that disturbs a gate post. The summer heat also punishes control boards and batteries inside operator housings, which is why electrical faults show up in this market about as often as mechanical ones. We answer 24/7 and offer fast dispatch from 7am to 7pm, Sunday through Friday.
Call (833) 408-4022 for a free estimate. The price is set per job by the written estimate, so nothing gets billed before you approve a number.
Gate Repair Cost Breakdown (2026)
These are typical estimated ranges for the Georgetown market in 2026. They cover parts and labor for a standard single-family driveway gate unless noted otherwise. Commercial operators and oversized gates cost more, and the written estimate always wins over any range on this page.
| Repair or service | Typical estimated range |
|---|---|
| Diagnostic visit and written estimate (applied to job scope, not the repair itself) | $0 – the estimate is free |
| Manual gate hinge, latch or wheel replacement | $185 – $360 |
| Manual gate sag or alignment correction (swing or slide) | $240 – $480 |
| Electric gate operator repair (control board, limit switch, receiver) | $280 – $650 |
| Photo eye, safety loop or safety edge replacement | $220 – $420 |
| Gate arm actuator or motor replacement (swing) | $520 – $1,100 |
| Slide gate track, roller or guide replacement | $380 – $850 |
| Chain, sprocket or drive assembly on a slide operator | $340 – $720 |
| Battery and backup system replacement | $180 – $340 |
| Keypad, remote receiver or entry intercom wiring repair | $210 – $480 |
| Post reinforcement or partial footing work (varies with soil and access) | $400 – $1,200 |
| Commercial operator repair (DoorKing, FAAC, BFT) | $450 – $1,400 |
| New electric gate installation | $3,200 – $8,500 |
A repair on a residential Mighty Mule or Ghost Controls operator usually lands at the low end of the electric gate range because those systems use affordable, widely available parts. A commercial FAAC, BFT or DoorKing operator often runs higher, since the diagnostics take longer and the parts cost more. The single biggest cost driver, though, isn’t the brand. It’s whether the gate’s mechanical frame is straight. An operator bolted to a sagging or warped gate will keep failing until the gate itself gets corrected, and that work adds $240 to $480 on top of the electrical repair in most cases we see.
What Affects Gate Repair Pricing in Georgetown
- Manual versus electric. A manual gate repair bills for hinges, latches, wheels and alignment. An electric gate repair adds the operator, control board, safety devices and low-voltage wiring, which is where most of the price difference sits.
- Operator brand and grade. Residential DIY-grade operators like Mighty Mule and Ghost Controls use parts that are cheaper and faster to source. Commercial systems like DoorKing and FAAC use heavier-duty parts that cost more but last longer. We’re trained on all nine major brands, so a Lincoln or BFT unit doesn’t leave us guessing.
- Limestone ground and footing condition. Georgetown sits on limestone across a lot of the city, particularly west of I-35. Digging near rock slows down any job that touches the posts, and gate posts that have tilted over the years are a common reason a slide gate stops closing square.
- Summer heat and operator housings. Central Texas summers are hard on control boards, batteries and receivers sitting inside an unvented operator box. Heat-related board failure is one of the more frequent electrical calls we get in Georgetown, and it’s a repair, not a replacement, most of the time.
- Gate size and weight. A single 12-foot swing gate is a much smaller job than a 20-foot double swing or a long slide gate. Heavier gates need larger actuators, sturdier hinges and more labor to align.
- Access and wiring runs. A gate at the end of a 200-foot driveway adds trenching or wire tracing time. Gates set tight against a fence line or a limestone wall are slower to work on than gates with open access on both sides.
- Safety device requirements. Photo eyes, safety edges and loop detectors aren’t optional on an automatic gate. If the gate is missing one or has a failed one, we’ll flag it in the estimate, since a missing safety device is a crush and entrapment risk.
Is Gate Repair Cheaper Than Replacing the Gate?
Repair is cheaper than replacement in most cases. A $280 to $650 operator repair beats a $3,200 to $8,500 new installation every time, and a $185 to $480 manual gate fix on a sound frame is a fraction of replacement cost. Replacement makes sense when the gate’s frame is bent or rusted beyond correction, when the posts have shifted into limestone and can’t be re-set reliably, or when a legacy operator has no available parts. That last point is worth checking before you commit to a new system, and one thing we do on a diagnostic visit is confirm whether the part on your gate is still manufactured. When it is, we repair. When it isn’t, we explain the replacement options and let you decide.
How to Save on Gate Repair
- Get the free estimate first. Call (833) 408-4022 and we’ll come out, diagnose, and give you a written price before any work starts. There’s no service-call fee and no diagnostic charge, so the only price you see is the price of the repair.
- Fix small mechanical problems before they reach the operator. A gate that’s been dragging on its track for months wears out the operator motor faster. Correcting a hinge or wheel at $185 to $360 beats replacing a $520 to $1,100 actuator later.
- Keep the operator housing clear. In Georgetown heat, a control board that can’t breathe runs hotter and fails sooner. Clearing debris and vegetation away from the housing is a free habit that stretches the life of the electronics.
- Consolidate the visit. If two things are wrong, a photo eye and a slipping chain, for example, ask us to quote both in one visit. The diagnostic work overlaps, and the second repair often costs less than it would on its own.
- Don’t skip the safety devices. A missing photo eye or safety edge isn’t a cost to defer. It’s a crush and entrapment risk, and installing one now costs less than correcting the aftermath of a gate that closes on a vehicle or a person.
- Ask about part availability before agreeing to replace. Many systems we see in Georgetown, including Linear, Elite and Viking, have parts that are still in production. Confirming that first can save a full installation.
If you want a second opinion on a big quote, that’s a fair reason to call. Call (833) 408-4022 for a free estimate and we’ll tell you plainly whether repair or replacement makes more sense for your gate.
What Does a Site Visit Include?
On a site visit, a technician will test the operator’s electrical connections, cycle the gate through its full open and close, and check the mechanicals, including hinges, rollers, track, chain and posts. We’ll identify the failure, confirm whether the part is in production, and write up an estimate with the exact price. A gate is a heavy moving object with an operator that carries mains power, so we never recommend homeowners open the operator housing or touch the low-voltage wiring themselves. A trained technician is the right person to trace a fault on a gate, both for the diagnosis and for safety. Our technicians have up to 13 years of experience, and we work on gates exclusively, which means we’re not splitting attention across fencing, garage doors or general handyman work. When you need gate repair Georgetown homeowners call us for, we arrive knowing the brand before we arrive at the gate.
Does Gate Repair Cost More for Commercial Systems?
Yes, usually. Commercial operators like DoorKing, FAAC and BFT use heavier-duty parts, and on a high-traffic commercial gate the diagnostic step takes longer. Expect $450 to $1,400 for a typical commercial operator repair, compared with $280 to $650 for a residential electric operator. A commercial gate used many times a day also wears faster, so a repair often includes adjusting or replacing the chain, sprocket or guide assembly alongside the electrical fix. If you manage a property in Georgetown with an automatic gate on a commercial operator, get a written estimate before anything is ordered. The gate capacity and duty cycle matter for the estimate, and we’d rather quote it right than quote it low. For routine gate repair on either a residential or commercial system, the process is the same: diagnose, quote, then fix.
Should You Repair or Install a New Gate?
Repair when the gate frame is straight, the posts are solid and the operator’s parts are still in production. Install new when the frame is bent, the posts can’t be re-set reliably in Georgetown’s ground, or the operator uses parts that are no longer made. New electric gate installation typically runs $3,200 to $8,500 for a residential driveway gate, with the final price depending on gate size, operator brand, access, and whether trenching is needed for the wiring. A manual gate installation costs less but still requires proper footing. If you’re upgrading from a manual gate to an automatic one, start with the free estimate, and we’ll walk through operator options that fit the gate you already have. The right system for a residential driveway is not the right one for a commercial entrance, and matching the operator to the gate’s weight and duty cycle is what keeps it working. Call (833) 408-4022 to talk through the options.
FAQs – Gate Repair Cost
How much does gate repair cost in Georgetown?
Gate repair in Georgetown typically costs $185 to $650 for a manual gate and $280 to $1,100 for an electric gate, with most common electric fixes landing between $280 and $520. Commercial operator repair runs $450 to $1,400. Call (833) 408-4022 for a free estimate, and the written price you get is the price you pay.
Can you fix my gate the same day?
Often, yes. Many gate repairs are completed in a single visit, especially common failures like photo eyes, limit switches, chains, hinges and batteries, since those parts are diagnosed and replaced on-site. Some jobs need a part ordered in, and in those cases we’ll confirm the timeline in the estimate. Call (833) 408-4022 to check same-day availability. We answer 24/7 and offer fast dispatch from 7am to 7pm, Sunday through Friday.
Is it cheaper to repair or replace an electric gate?
Repair is cheaper in most cases. A typical operator repair at $280 to $650 is far less than a new installation at $3,200 to $8,500. Replacement makes sense when the gate’s frame is bent, the posts can’t be re-set, or the operator’s parts are no longer manufactured. Call (833) 408-4022 and we’ll tell you honestly which path fits your gate, with a free written estimate either way.
How much does a new gate installation cost in Georgetown?
A new electric gate installation in Georgetown typically costs $3,200 to $8,500, depending on gate size, operator brand, access and wiring. Manual gate installation runs lower but still includes proper footing. If you’re weighing installation against repairing your existing system, call (833) 408-4022 for a free estimate, and we’ll compare both numbers for you.
Do you work on my gate brand?
Probably yes. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule, which covers the large majority of residential and commercial operators in the Georgetown market. Whether yours is a residential Mighty Mule or a commercial DoorKing, we know the system. Call (833) 408-4022 to confirm your model and get a free estimate.
Pricing reflects the Georgetown market as of 2026. Gate Repair Georgetown offers free estimates – call (833) 408-4022. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Georgetown.
What Our Customers Say
"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
- Carmen Morales"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Lisa Anderson"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Jennifer Norris