Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Electric Gate Repair for Georgetown Homeowners
An electric gate that won’t open is a driveway you can’t use and a property line that no longer does its job. Gate Repair Georgetown focuses only on gates, so our technicians read the operator, the arm, and the access hardware as one system instead of guessing at a general fix. Some of them bring up to 13 years of hands-on experience, and they work on the same nine brands day after day. We answer 24/7, and a call placed during dispatch hours is often met the same day. We’re licensed and insured, and we quote and agree on the price before any work starts. Call (833) 408-4022 and tell us what the gate is doing.
Gate Opener Repair
Gate Opener Repair is the work of fixing the box and arm that actually move your gate, and it’s the first thing we check when a gate stalls, reverses, or stops responding. You need it when the motor hums but nothing moves, when the gate runs a few feet and quits, or when the remote works only up close. We diagnose the opener on the spot, from the control board and limit switches to the drive gears inside the housing. On Georgetown properties we see a lot of these calls after a stretch of hard, dry weather has worked grit into moving parts. An opener repair typically runs $150-$450 depending on the fault and the parts your unit needs, and that estimate is written and agreed before we start.
Control Board and Limit Switch Faults
A board that has taken a power surge or a limit switch that drifted out of position will make a good gate act broken. We test the board’s inputs and reset the travel limits rather than swapping the whole opener. If the board itself has failed, we identify the correct replacement for your brand.
Arm and Gear Assembly Wear
Swing and slide arms wear at the pivot points and inside the gearbox, which shows up as grinding, slipping, or a gate that drifts open on its own. We pull the arm and check the gear mesh before recommending a rebuild or a replacement arm. Worn gears usually give warning before they fail outright, so catching them early saves the motor.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Automatic Gate Repair
Automatic Gate Repair covers everything that makes a gate open by itself: the operator, the safety sensors, the wiring between them, and the control hardware that ties it together. You need it when the gate reverses on nothing, ignores the remote, stops halfway, or runs when it shouldn’t. We treat the whole automatic system as one unit rather than chasing one part at a time, which is why a Mighty Mule residential arm and a heavier FAAC system both get a proper diagnosis. We watch the gate cycle and check the travel, the safety edges, and the obstacle response to find the actual cause. Typical automatic gate repair in Georgetown runs $180-$550 depending on the operator and what has failed. You’ll get a free on-site estimate with the price set before any work begins.
Safety Edge and Obstacle Sensing
A gate that won’t reverse when it meets something is a real hazard, especially with children and pets around the driveway. We test the safety edges and the operator’s force settings and correct them to spec. Any adjustment here is done by a trained technician, because the sensing and force limits are the part of an automatic gate that protects people.
Wiring and Low-Voltage Connections
Loose low-voltage connections and a damaged run from the control box to the keypad are behind a surprising share of “dead” gates. We trace the wiring and the power run to confirm what’s actually wrong. Exposed outdoor wire and connections at the posts get checked as part of the same visit.
Electric Gate Motor
The Electric Gate Motor is the drive unit that turns a manual gate into an automatic one, and it’s the part most likely to fail first under constant use. You need motor attention when you hear grinding, the gate moves slowly, it labors on a slope, or a recently working motor suddenly won’t start. We diagnose the motor itself along with its power supply and controller, and we know where each brand’s drives wear out. Because we work only on gates, the motor diagnosis is faster and there’s less trial-and-error swapping of parts. Electric gate motor repair in Georgetown typically costs $200-$650 depending on the unit and whether the motor is rebuilt or replaced. The free estimate gives you the number before anyone touches a tool.
Slope and Weight Loads
A motor sized for a light gate on flat ground will overheat on a heavier gate or a slope, and that’s the failure we find most often on hill-country properties around Georgetown. We measure the gate and check the drive against the real load it’s moving. Getting the load right prevents repeat failures.
Power Supply and Controllers
The motor is only as reliable as the power and controller feeding it, and a weak supply or a misconfigured controller mimics a dead motor. We test voltage at the motor and the control inputs before condemning the drive. If the supply is the problem, we fix that instead of selling a motor you don’t need.
Gate Access Control
Gate Access Control is the system that decides who gets through: keypads, remotes, receivers, intercoms, and the entry hardware wired to your operator. You need it looked at when a code stops working, the keypad won’t power up, a remote drops out, or you need to add or remove users after a move or staff change. We service access hardware across DoorKing, Linear, and other entry systems and tie it back to the operator it controls. We test each entry point and the receiver so the problem is isolated before we change anything. Access control repair in Georgetown generally runs $120-$400 depending on the hardware. That’s an estimate, and the written quote you approve sets the final price.
Keypads, Receivers, and Remotes
A keypad that beeps but won’t open, or a remote that only works close to the gate, usually points to the receiver, the antenna, or a dead battery in the entry device. We test the signal and the receiver together instead of replacing parts by guesswork. Pairing and reprogramming entry devices is part of the same visit.
Intercoms and Entry Hardware
Intercoms and entry stations share wiring with the operator, so a fault in one can knock out the other. We trace the connection and confirm the entry hardware talks to the gate the way it should. This is service work on gate entry systems only, not general low-voltage electrical.
Commercial Gate Operator
A Commercial Gate Operator is built for far more cycles and heavier traffic than a residential arm, and it fails in different ways. You need this section when a business entrance, a managed property, or a high-traffic driveway starts acting up during peak hours. We service commercial-grade operators from FAAC, BFT, DoorKing, and LiftMaster, and we understand the duty cycle and the safety requirements those systems carry. We check the drive, the controls, and the safety devices together so a busy entrance isn’t taken down twice. Commercial gate operator repair in Georgetown typically runs $250-$800 depending on the operator and the fault. We quote it in writing before work begins, and on gate work of this scale we schedule the visit rather than promise a same-day fix.
Duty Cycle and Heavy Traffic
A residential-grade arm pushed into commercial use overheats and quits, which is why matching the operator to the traffic matters. We look at how often the gate cycles and whether the drive is rated for that pace. Getting the duty cycle right is the difference between one repair and a string of them.
Safety Devices on Busy Entrances
Loop detectors, safety edges, and photo eyes on a commercial gate protect vehicles and people, and a fault there stops the gate for good reason. We test each device and correct the settings so the gate runs and stays safe. This work is handled by a trained technician, because commercial safety devices are not a do-it-yourself adjustment.
Brands We Service
We work on the operators you’re most likely to own, and we know each one’s habits. With Elite, we know the residential swing and slide units and where the control board and limits tend to give trouble. On Mighty Mule and Ghost Controls, the DIY-grade systems many homeowners install themselves, we know the common arm and battery failures and how to sort them without throwing parts at the gate. LiftMaster and FAAC cover a wide tier from home swing gates to heavier commercial drives, and we’ve seen their wear patterns across both.
Viking, Linear, DoorKing, and BFT round out the list, and each has its own quirks in the controller, the entry hardware, and the drive. Because gates are all we work on, the parts familiarity and faster diagnosis show up on every call. Whether you have a LiftMaster arm, a FAAC slide operator, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate won’t reverse on an obstacle. This is the safety function that protects people and vehicles, and it’s the one we never advise testing yourself with a hand or a body part. If the gate doesn’t stop and back off when it meets resistance, call a technician.
- The motor hums but the gate doesn’t move. A hum with no movement points to a seized drive, a stripped gear, or a binding track. Continuing to run it can burn out the motor and turn a smaller repair into a bigger one.
- The gate reverses or stops for no reason. Intermittent behavior from a failing limit switch or a bad safety edge is a sign the operator is confused about where the gate is. A specialist can trace it to the actual part instead of replacing the whole unit.
- Grinding or clunking during travel. Noise through the arm or track means metal is wearing against metal. Catching it early usually means a rebuild; ignoring it means a new arm or motor.
- A code or remote suddenly stops working. This can be as simple as a battery, but it can also be a receiver or access-control fault. Getting it checked keeps the gate secure rather than propped open.
Our Process, Step by Step
- 1
You call (833) 408-4022 and describe what the gate is doing. We answer 24/7, and during dispatch hours a Georgetown call is often booked the same day. We ask the brand, gate type, and what changed so the technician arrives ready.
- 2
We come out and run the gate through a full cycle while watching the operator, the arm or track, and the safety devices. This is where a gate-only specialist earns the visit: we’re reading the system, not the component in isolation.
- 3
We test the parts that matter, from the control board and limit switches to the motor supply and the access hardware. We isolate the fault instead of swapping parts by guesswork. That’s how we keep the repair down to what the gate actually needs.
- 4
You get a free written estimate with the price set before any work starts. We walk you through what failed and what it takes to fix it correctly, so there’s no surprise when the work is done. If the issue is a worn part rather than a dead one, we tell you that too.
- 5
We complete the repair, test the gate through repeated cycles, and confirm the safety functions behave as they should. You get a gate that opens, closes, and stops the way it’s supposed to. Any follow-up need you have, the same specialists handle it.
How Much Does Electric Gate Repair Cost in Georgetown?
Electric gate repair in Georgetown typically runs $150-$800 depending on the operator, the fault, and whether parts are rebuilt or replaced. A simple opener fix like a limit switch is usually $150-$450, while a motor or commercial operator repair lands higher. A gate that needs a new control board or a corrected power supply sits in the middle of that range.
What affects the price: the brand and grade of operator, whether it’s a residential arm or a commercial drive, the condition of the wiring, and how far the gate is from the controls. A gate that has been binding for months costs more to fix than one caught early. Slopes and heavier panels around Georgetown also put more load on a motor and can change the part it needs.
How to avoid overpaying: get a written estimate, confirm what’s included, and be wary of anyone who wants to replace the whole operator without testing the individual parts. We diagnose first so the repair is matched to the actual failure.
Every free estimate you get from us includes the diagnosis and a written price set before work starts. There’s no service-call fee, and you approve the number before anyone begins. For exact pricing on your gate, call (833) 408-4022; estimates are free.
Our Service Area Near Georgetown
We work across Georgetown and the surrounding communities: Jarrell, Bartlett, Bertram, Holland, Round Rock, Weir, Thrall, Thorndale, and Little River-Academy. Gate repair is handled the same way regardless of address, with a free written estimate and the price set before any work starts. For more of what we cover, see Gate Repair Georgetown, and for the automated systems in a nearby town, our electric gate repair page covers Jarrell. Call to schedule, and we’ll book the visit around your location.
Serving Georgetown, TX – Our Local Coverage Area
We serve Georgetown and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Electric Gate Repair in Georgetown
Electric gate repair is the diagnosis and fixing of the motor, controller, wiring, safety devices, and access hardware that make an automatic gate operate. It’s different from general repair because the parts have to work together as a system. We handle the operator and the entry controls, but not garage doors or fencing, since gates are all we do.
Most electric gate repairs are completed in a single visit, often in an hour or two once the fault is found. Some jobs take longer when a part has to be ordered for a specific brand or commercial operator. We confirm the timeline after the diagnosis, so you know what to expect.
Electric gate repair in Georgetown typically costs $150-$800 depending on the operator and the fault, with simpler opener fixes near the low end and motor or commercial repairs higher up. The estimate is free and written, and you approve the price before any work starts. Call (833) 408-4022 for an exact quote; estimates are free.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the odds are good your operator is on the list. If you have a different make, call and describe it. We’ll tell you straight whether it’s a system we can fix.
Same-day service is often possible on gate repairs when you call during dispatch hours. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday; we’re closed Saturday. A call outside dispatch hours is booked into the next opening.
Reach out and we’ll confirm the exact coverage in writing on your estimate before work begins. Warranty terms can vary with the part and the job. That way you know precisely what’s covered.
Clear the area around the gate so the technician can run it through a full cycle safely, and if you have the manual or the brand name and model, have it handy. Note when the problem started and what the gate does when it fails. If the gate is stuck closed and you depend on it for access, say so when you call so we can plan the visit.
Schedule Your Electric Gate Repair Service in Georgetown Today
A gate that won’t work is worth fixing right. Call (833) 408-4022 for a free, no-obligation estimate on electric gate repair in Georgetown. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 13 years of experience, the price is agreed before work starts, and the work is guaranteed. Let’s get your gate moving.
Written by the team at Gate Repair Georgetown.