Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateWhy Georgetown Homeowners Choose Ghost Controls Gate Repair
We provide independent Ghost Controls gate repair service in Georgetown, TX. Our technicians have up to 13 years of experience with Ghost Controls swing operators, diagnosing control boards, battery banks, solar charging, and arm geometry on systems that were installed by the homeowner and tuned by trial and error. That’s what sets our Ghost Controls work apart: we know what a DIY-installed operator looks like in the field, and we fix the cause instead of swapping parts.
We are an independent service provider. We are not affiliated with, authorized by, or endorsed by Ghost Controls. We repair, install, and service Ghost Controls equipment with quality parts that fit it, and we also work on LiftMaster, Mighty Mule, and DoorKing operators when that’s what you own.
Call (833) 408-4022. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- We repair and install Ghost Controls swing operators as an independent service, not as a dealer or an authorized warranty center.
- Most Ghost Controls no-start and erratic-limit calls trace back to battery, solar, or gate-alignment problems, not a dead control board.
- Georgetown’s Hill Country clay and limestone ground moves gate posts out of plumb, which strains Ghost Controls arms and limit magnets.
- The estimate is free, and the price is quoted and agreed before any work starts.
Why Trust Gate Repair Georgetown for Your Ghost Controls Gate Repair?
Ghost Controls is a DIY-oriented line. That means the installs and settings we encounter in Georgetown are wildly inconsistent, and that’s exactly the kind of system we know best. One gate runs a single swing operator with a small solar panel wired backward. Another runs a double-gate kit with a completely unrelated brand’s arm bolted on. We walk up, read the setup, and work from what’s actually there.
Our technicians work on Ghost Controls operators without any manufacturer authorization or warranty relationship. That independence matters to you: we’re not steering you toward a new unit to satisfy a sales quota, and we’re not bound to one brand’s parts pipeline. We diagnose the controller, the battery bank, and the gate’s mechanical geometry as three connected systems, because on a Ghost Controls install they fail together.
We specialize exclusively in gates, all we do, which means the parts familiarity runs deep and the diagnosis is fast. Where a generalist guesses, we test. Swing arm wear, clevis pin slop, and a gate that has sagged out of plumb all show up on the operator as the same symptom, and only a technician who works these systems every day can tell them apart in one visit.
Call (833) 408-4022 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Common Ghost Controls Gate Repair Problems We Fix in Georgetown
The failure modes below are what a DIY-installed Ghost Controls operator actually does when it goes wrong. Georgetown’s climate and soil push several of them along faster than the manuals suggest.
- Control board faults from moisture and reversed polarity. DIY solar and battery wiring is where these boards take damage. A panel or battery bank hooked up in reverse, or a controller housing that collects condensation through a Central Texas summer, can take the board out. The gate stops mid-travel, runs one direction only, or quits entirely. We test the board before condemning it, because polarity damage and a weak battery read almost the same at first.
- Battery bank sulfation on solar units. This is the most common Ghost Controls complaint we see in Georgetown. When the panel is undersized for the gate’s actual daily cycles, or shaded part of the day, the battery never fully recovers its charge. The gate works through the morning and quits at dusk, or the limit behavior turns erratic as voltage sags. A battery that reads fine at rest can collapse under load, so it has to be tested under load.
- Swing arm and actuator wear. Bent or seized arms, worn clevis pins, and gates that have sagged out of plumb make the operator strain against the hinge through every cycle. On Georgetown’s expansive clay, posts heave out of plumb after wet-dry swings and hard freezes, so an arm that was aligned at install is fighting the gate a year or two later. That strain wears the arm and the operator motor.
- Limit-switch and magnet drift. The limit magnet is a small part with a big job, and a hard freeze, a settling post, or a gate that racks after a rain cycle can knock it out of position. The result is over-travel, short cycling, or a gate that reverses on contact. Recalibrating limits is a quick job once we’ve confirmed the gate itself is plumb.
- Erratic behavior after storm or freeze cycles. Georgetown sits on the eastern edge of the Texas Hill Country, where the soil is thin limestone and clay, and gates here shift and rack more than in the flat blackland prairie towns nearby. That movement throws off arm geometry and limits repeatedly if the posts and hinges aren’t corrected first.
Ghost Controls Parts & Our Repair-vs-Replace Approach
Ghost Controls sells its own replacement control boards, arms, batteries, and remotes directly, and those are the right call when the controller is the confirmed fault. We don’t stock or carry OEM or genuine Ghost Controls parts, but we source quality parts that fit the system and match its specs. Where an aftermarket battery or piece of hardware meets spec, it’s a sound choice, and we’ll tell you so.
The repair-vs-replace decision usually comes down to one question: has the operator already been replaced once while the gate was still sagging or misaligned? When a board or arm has been swapped and the gate is still fighting itself, the honest answer is to fix the gate and mounting first. Re-plumb the posts, correct the hinges, re-anchor the operator bracket, then reassess the electronics. Buying another operator before that just repeats the failure.
Call (833) 408-4022 for a free estimate on your Ghost Controls gate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Our Ghost Controls Service Process – Step by Step
- 1
Diagnosis. We test battery voltage under load and solar output first, then check arm travel, clevis pins, and gate plumb before we touch the control board. That order matters on Ghost Controls systems, because a weak battery and a failing board produce overlapping symptoms.
- 2
Repair or install. Once we know the cause, we repair the confirmed fault or install the operator with the geometry set correctly. On a solar single-swing or dual-swing kit, that means the panel placed where it gets real sun, the battery bank wired to polarity, and the arm travel matched to the gate’s actual swing.
- 3
Test. We cycle the gate through full travel, recalibrate the limit magnets, check the reverse-on-contact sensitivity, and confirm the battery holds up through repeated cycles without the panel assisting.
- 4
Written estimate and follow-through. The price is quoted and agreed before any work starts, so the invoice matches what you approved. We don’t offer maintenance plans or service contracts, but if a post shifts again after a freeze, you’ll know exactly what to describe when you call.
See the difference
Before
After
Before
After
Before
AfterGhost Controls Products We Service & Install in Georgetown
We service and install the Ghost Controls swing operators you’re likely to own: the Heavy-Duty Single Swing (TSS1) automatic gate opener, the Dual Swing (TDS2) double gate opener kit, the Solar-Ready Single Swing (TSA1) with a 10W panel, and the Architectural Series swing openers. That covers single and double swing gates on residential driveways and entry gates alike. We handle the full gate lifecycle from new installation through repair, so you don’t need a second contractor as your needs evolve. Whether your operator is a Ghost Controls or a commercial FAAC system, we know it, and we service both residential and commercial-grade gate operators across Georgetown.
We Also Service These Brands
Ghost Controls is one of nine major gate brands we work on. We also service LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite. If you move to a different operator or manage a property with a mix of brands, you don’t need a new contractor. Your gate brand is on our list, and we know it inside out.
FAQs – Ghost Controls Gate Repair Service in Georgetown
No. We are an independent Ghost Controls service provider. We are not affiliated with, authorized by, or endorsed by Ghost Controls, and we have no warranty relationship with the manufacturer. We repair, install, and service Ghost Controls equipment with quality parts that fit it, using our own diagnosis and our own written estimate.
Yes. We use parts that fit and match the specs of your Ghost Controls system, including control boards, arms, batteries, remotes, and hardware. We don’t stock or carry OEM or genuine Ghost Controls parts, and we’re not a dealer. When a component needs to come from the manufacturer’s own replacement line, we’ll tell you that plainly.
Most Ghost Controls repairs in Georgetown are done in a single visit, usually within an hour or two once the fault is confirmed, though board or arm replacements and realignment work can run longer. We don’t promise same-day service for every job; the diagnosis comes first, then the written estimate sets the timeline. Call (833) 408-4022 for an exact quote, estimates are free.
We cover the Heavy-Duty Single Swing (TSS1) operator, the Dual Swing (TDS2) double gate opener kit, the Solar-Ready Single Swing (TSA1) with a 10W panel, and the Architectural Series swing openers. That includes control boards, battery banks, swing arms, actuators, clevis pins, limit magnets, and remotes. If you’re not sure which one you own, describe the gate and we’ll figure it out.
Service by an independent provider may affect a manufacturer warranty, and you should check the terms of your own warranty before scheduling. We can talk through what we plan to do and how it might interact with your coverage. We don’t claim any manufacturer authorization, and we won’t describe our work as factory-approved.
Ghost Controls gate repair in Georgetown typically runs from around $150 to $450 for most single-visit fixes, with battery replacement and limit recalibration at the low end and control board or arm replacement at the upper end. Installation of a new operator is priced separately after we measure the gate. The estimate is free, the price is quoted and agreed before any work starts, and the written estimate sets the final price. Call (833) 408-4022 for an exact quote, estimates are free.
Not necessarily. A gate that opens a few feet and stalls is often a battery sagging under load, a limit magnet out of position, or an arm binding on a gate that has sagged out of plumb, and any of those look like a board fault from the outside. We test battery voltage under load and check arm travel before condemning the controller. Call (833) 408-4022 for an exact quote, estimates are free.
A solar Ghost Controls opener that fails at night or on cloudy days is almost always running on a battery bank the panel can no longer keep charged. An undersized or shaded panel, or a battery that has sulfated over time, leaves the system short on voltage exactly when the sun isn’t helping. On a solar single-swing install, the gate commonly goes dead at dusk or starts reversing randomly, and it’s usually an aging battery bank paired with a limit magnet knocked out of position. A qualified tech tests battery voltage under load and solar output first, then checks arm travel, clevis pins, and gate plumb before touching the control board. Call (833) 408-4022 for an exact quote, estimates are free.
Usually not without the right receiver, because remotes have to match the operator’s radio frequency and coding. Mixing brands is one of the most common inconsistencies we find on DIY Ghost Controls installs. We can check what your controller actually accepts and sort out the pairing. Call (833) 408-4022 for an exact quote, estimates are free.
Yes, the reverse-on-contact sensitivity is adjustable, and on most Ghost Controls systems it’s a controller setting rather than a hardware swap. That said, a gate reversing too early can also be a limit magnet drift or a binding hinge tricking the operator into thinking it hit something. We calibrate the sensitivity after confirming the gate swings freely. Call (833) 408-4022 for an exact quote, estimates are free.
Yes, Ghost Controls operators can be set up with a keypad or app-based control for guests, though the exact option depends on the controller you have. We install and wire the accessories and confirm everything cycles correctly. Call (833) 408-4022 for an exact quote, estimates are free.
Book Your Ghost Controls Service in Georgetown, TX
If your Ghost Controls gate is stopping mid-travel, failing at dusk, or reversing on contact, we’ll diagnose it properly and quote the price before any work starts. Call (833) 408-4022 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Gate Repair Georgetown.