Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Georgetown?
Gate parts and welding in Georgetown typically run $150 to $2,200 depending on what failed. A simple hardware swap like hinges, rollers, or a latch usually lands between $150 and $400, a welded repair to a post, frame, or hinge point runs $250 to $650, and replacing a control board, motor, or arm assembly on an automated operator climbs to $450 to $2,200. The written estimate you get after we look at the gate sets the final price.
What pushes a job toward the top of that range is rarely the part itself. It’s access, gate weight, and whether the failure is a worn component or a bent frame that needs to be cut, squared, and re-welded before anything bolts back on. We work on gates only, across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the diagnosis is usually quick and the right part is the one that goes back on. Our technicians have up to 13 years of experience.
Key takeaways:
- Most hardware-only gate part repairs in Georgetown fall between $150 and $400.
- Welded structural repairs usually run $250 to $650, priced after we see the gate.
- Operator parts (boards, motors, arms) are the biggest line item: $450 to $2,200.
- Estimates are free, and the price is set per job in writing before any work starts.
Gate Parts & Welding Cost Breakdown (2026)
Here’s how the line items break down for the Georgetown market. These are typical estimated ranges, not quotes. The exact number depends on your gate, your operator, and what we find on the on-site estimate.
| Part or service | Typical estimated range | Notes |
|---|---|---|
| Hinges, rollers, and latches | $150 – $400 | Most common manual gate hardware call |
| Gate frame or post weld repair | $250 – $650 | Cut, square, and re-weld a bent or cracked member |
| Hinge-point weld and re-hang | $300 – $700 | Heavier swing gates that have sagged |
| Operator control board | $450 – $1,100 | Board cost varies widely by brand and model |
| Operator motor or gearbox | $600 – $1,800 | Residential through commercial-grade units |
| Swing arm or slide rack assembly | $350 – $900 | Includes alignment and travel reset |
| Safety sensors and photo eyes | $200 – $550 | Pair plus wiring and re-test |
| Loop, keypad, or entry device | $250 – $800 | Depends on device and existing wiring |
Two things move these numbers the most. First is operator brand and tier: a Mighty Mule or Ghost Controls residential unit uses less expensive parts than a FAAC, BFT, or DoorKing commercial operator, and that difference shows up in the parts cost. Second is whether the gate needs welding before the hardware can go back on. A gate that’s only missing a roller is a short job. A gate whose hinge has torn out of the frame, or whose post has shifted, needs the metal fixed first, and that’s where welding labor enters the estimate.
We don’t quote from a phone description when we can help it. A gate that looks like a simple part swap in a photo often turns out to have a bent hinge plate behind it, and welding that properly takes longer than bolting on a new hinge. The written estimate you get after we see the gate is what you pay, and it’s free. If you want to understand the wider repair picture, see our gate repair Georgetown page.
What Affects Gate Parts & Welding Pricing in Georgetown
Georgetown gates deal with a specific set of conditions: hot, dry summers, alkaline clay soil, and a growing number of automated residential and commercial entrances. Each of these pushes pricing in a known direction.
- Gate material and weight. A light ornamental aluminum gate and a heavy steel or cedar-clad estate gate are different jobs. Heavier gates need bigger hardware, more welding, and sometimes a second technician to lift and re-hang. That’s the single biggest reason two gates with the same visible problem price differently.
- Operator brand and grade. Residential-grade operators like Mighty Mule and Ghost Controls carry less expensive boards and arms than commercial operators like FAAC, BFT, and DoorKing. We stock familiarity with all of them, so the diagnosis is fast either way, but the parts cost reflects the tier.
- Whether welding is needed. Hardware swaps are quick. Welding a cracked frame, a torn hinge point, or a post that has pulled out of the ground is a longer job and requires the gate to be stabilized first. A gate that has been dragging or slamming for months usually needs both.
- Local soil movement. The clay soil around Georgetown swells and shrinks with the wet and dry season, and gate posts set in it can shift or lean over time. When a post has moved, the fix is often a reset and re-weld rather than a part swap, because no hinge will stay true on a post that’s out of plumb.
- Access and gate type. A slide gate with a long track and a clear approach is faster to work on than a swing gate wedged between masonry pillars or set back behind landscaping. Slide gates that have jumped the track also bring a real safety concern, which we address below.
- Age of the operator and parts availability. Older operators sometimes need a board or arm that isn’t a stock item, which affects lead time and price. When a part is discontinued or back-ordered, we’ll tell you and lay out the options in the estimate rather than guessing at a substitute.
Because we specialize exclusively in gates, we’re not splitting attention between fences, garage doors, and general handyman work. That focus shows up in faster diagnosis and fewer return visits. If you want the broader sense of how gate work is priced in this market, our Georgetown page covers repair and installation across the area.
What to Check Before You Call
You don’t need to diagnose the gate yourself, and on anything involving the operator’s power or wiring you shouldn’t. But a few details help us quote accurately. Note the operator brand if it’s printed on the housing. Describe whether the gate is swing or slide. Check whether the gate is dragging, sagging, or binding at a hinge. And if the gate has stopped moving entirely, check the power first, but don’t open the operator housing. Wiring and power to an automated gate carry the same hazard as any outdoor electrical equipment, and the operator’s internal components can hold stored energy even after power is cut. That’s work for a trained technician, and we’ll handle it on the visit.
A gate that has come off its track or is hanging by a single hinge is a crush hazard, especially on a heavy slide gate. Keep people and vehicles clear of it until it’s fixed, and don’t try to force it back by hand. Call us and we’ll get someone out.
How to Save on Gate Parts & Welding
The biggest savings on gate parts and welding in Georgetown come from catching a small problem before it becomes a structural one. A worn roller that gets replaced for $150 to $400 is a far smaller bill than a hinge point that tears out of the frame and needs welding and re-hang at $300 to $700, or a gate that sags onto its operator and burns out a motor or control board in the $600 to $1,800 range.
- Fix the first symptom. If the gate is starting to drag, stick, or bind at a hinge, get it looked at. Wear compounds fast on automated gates, and the part that fails second is usually more expensive than the one that failed first.
- Keep the track and hinges clear. Dirt and grit in a slide track and at hinge points accelerate wear. A simple clean-out costs nothing and buys time before the next part.
- Don’t over-operator an old gate. Matching a heavy gate to an undersized operator wears both out. On a replacement, it’s worth sizing the operator to the actual gate weight rather than price alone.
- Get a written estimate before work starts. Estimates are free, and seeing the line items tells you whether you’re paying for a part, welding, or both. It also lets you compare fairly against any other quote.
- Ask about the repair-versus-replace line. For an older operator or a badly bent gate, we’ll tell you straight whether repair is the better spend or whether the money is better put toward a new operator or a new gate. We install, so we’re not steering you toward a repair just because that’s the job in front of us.
For a free estimate on your specific gate, call (833) 408-4022. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Repair or Replace? How to Decide
A gate frame that’s sound and just needs hardware or a single weld is almost always worth repairing. A gate whose frame has rusted through at multiple points, or whose post has shifted so far that the gate no longer aligns with its catch, often costs more to keep patching than to replace. On the operator side, a control board or motor on an otherwise good unit is a repair. A unit that has needed major parts two or three times and is now hard to source is usually a replacement candidate. We’ll give you both numbers in the estimate so you can see the gap for yourself.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Georgetown?
Gate welding in Georgetown typically runs $250 to $650 for a frame or post repair, and $300 to $700 when a hinge point has to be rebuilt and the gate re-hung. The number depends on how much metal has to be cut out and replaced and whether the gate has to come off its hinges to square it up. Heavy gates take longer to stabilize, which is the usual reason a job lands at the top of the range. Call (833) 408-4022 for a free on-site estimate.
What does a replacement gate operator part cost?
A control board usually falls between $450 and $1,100, and a motor or gearbox between $600 and $1,800, depending on the brand and tier. Residential-grade operators like Mighty Mule and Ghost Controls sit at the lower end; commercial operators like FAAC, BFT, and DoorKing sit higher because the parts are built for heavier duty cycles. The brand on the housing is the quickest way to know where you’ll land. Call (833) 408-4022 and we’ll give you a written number.
Is it cheaper to repair a gate or replace it?
Repair is cheaper in most cases: a hardware or weld repair at $150 to $700 against a full replacement. Replacement only wins when the frame is rusted through or the post has shifted badly enough that patching won’t hold, or when an older operator needs major parts it can’t readily get. We’ll quote both a repair and a replacement in the same estimate so the comparison is honest. Call (833) 408-4022 for that estimate.
Do you charge for a gate parts and welding estimate in Georgetown?
No. The estimate is free, and the price you’re given in writing is the price. We look at the gate and operator on site and set the cost per job based on what’s actually needed, rather than a phone guess. If the diagnosis reveals a different problem than expected, you’ll see it in the estimate before any work starts. Call (833) 408-4022 to set one up.
Can you fix a slide gate that has come off its track?
Yes, and it’s worth calling rather than forcing it back by hand. A slide gate off its track is heavy, unstable, and a crush hazard, and the rack or rollers are often damaged in the process. We repair and realign slide gates and their operators across all the major brands. Call (833) 408-4022. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Which gate brands do you work on?
We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers most residential systems and a good share of commercial operators you’ll find on Georgetown properties. Because we specialize in gates only, we know these systems well enough to diagnose fast and fit the right part the first time. Call (833) 408-4022 with your brand and model and we’ll take it from there.
Get a Free Gate Parts & Welding Estimate in Georgetown
If your gate is dragging, sagging, stuck, or hanging by a hinge, don’t wait for it to get worse. The smaller the problem, the smaller the bill, and a weld or hardware fix costs far less than a burned-out operator. We specialize exclusively in gates, from manual swing gates to commercial automated operators, and we’ve seen the make and model you own. Call (833) 408-4022 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Same-day service is often available, and the written estimate sets the final price before any work begins.
Pricing reflects the Georgetown market as of 2026. Gate Repair Georgetown offers free estimates – call (833) 408-4022.
Written by the team at Gate Repair Georgetown.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, swapped it, and we were moving cars again in under an hour."
- Neil Ackerman"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Veronica Rodriguez"Fixed the immediate problem. He was honest that the operator is near end of life and I should budget for a replacement, which I appreciate even if it wasn't what I wanted to hear."
- Gabriela Salazar